| Specification |
Description |
| Power supply
|
120 V AC, 9 A, 50/60 Hz; 220-240 V AC, 4.7 A, 50/60 Hz |
| Power Consumption (120V AC, 50/60Hz)
|
925 W (1,010 VA) (0.2 W with standby mode set to eco. 6 W with standby mode set to normal. Both with fan stopped.) |
| Power Consumption (220-240V AC, 50/60Hz)
|
900 W (980 VA) (0.3 W with standby mode set to eco. 9 W with standby mode set to normal. Both with fan stopped.) |
| DLP™ chip Panel size
|
24.4 mm (0.96 inches) diagonal (16:10 aspect ratio) |
| DLP™ chip Display method
|
DLP™ chip x 3 (R, G, B), DLP™ projection system |
| DLP™ chip Pixels
|
2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels |
| LENS
|
Optional powered zoom/focus lenses |
| Lamp
|
355 W UHM lamps (x 2) (dual lamp, normal mode) |
| Screen size
|
1.78-25.4 m (70-1,000 inches) (1.78-15.24 m (70-600 inches) with the ET-D75LE8), 16:10 aspect ratio |
| Brightness
|
10,600 lumens (dual lamp, normal mode) |
| Center-to-corner uniformity
|
90% |
| Contrast
|
10,000:1 (full on/full off, in dynamic iris 3 mode) |
| Resolution
|
1,920 x 1,200 pixels |
| Scanning Frequency (SDI)
|
3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p; 3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p; HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p; SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 525i(480i), 625i(576i) |
| Scanning Frequency (HDMI/DVI-D/RGB)
|
Horizontal: 15 kHz-100 kHz, vertical: 24 Hz - 120 Hz, dot clock: 25 -162 MHz or lower (HDMI/DVI: 25 MHz - 162 MHz) |
| Scanning frequency YPBPR (YCBCR)
|
525i(480i): fH 15.75 kHz; fV 60 Hz, 625i(576i): fH 15.63 kHz; fV 50 Hz, 525p(480p): fH 31.50 kHz; fV 60 Hz, 625p(576p): fH 31.25 kHz; fV 50 Hz, 750(720)/60p: fH 45.00 kHz; fV 60 Hz, 750(720)/50p: fH 37.50 kHz; fV 50 Hz, 1125(1035)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/50i: fH 28.13 kHz; fV 50 Hz, 1125(1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125(1080)/24p: fH 27.00 kHz; fV 24 Hz, 1125(1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125(1080)/30p: fH 33.75 kHz; fV 30 Hz, 1125(1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125(1080)/50p: fH 56.25 kHz; fV 50 Hz |
| Scanning Frequency (Video/S-Video)
|
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60] fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
| Optical axis shift Vertical
|
±55% (±44% with the ET-D75LE6) from center of screen, powered; NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50. |
| Optical axis shift Horizontal
|
±20% (±15% with the ET-D75LE6) from center of screen, powered; NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50. |
| Keystone correction range
|
Vertical ±40°, Horizontal ±15°(vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6) When using only the KEYSTONE correction of the Geometric Adjustment function: Vertical ±40°, horizontal ±15° |
| Installation
|
Ceiling/floor, front/rear |
| Terminals SDI IN
|
BNC x 1, 3G-SDI signal: SMPTE ST 424 compliant; HD-SDI signal: SMPTE ST 292 compliant; SD-SDI signal: SMPTE ST 259 compliant |
| Terminals HDMI IN
|
HDMI 19-pin x 1, Deep Color, compatible with HDCP,525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz -162 MHz; NOTE: Compatible with non-interlaced signals only. |
| Terminals DVI-D IN
|
DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz -162 MHz; NOTE: Compatible with non-interlaced signals only. |
| Terminals RGB 1 IN
|
BNC x 5 |
| Terminals RGB 1 IN R, G, B
|
R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. |
| Terminals RGB 1 IN Y, PB, PR (Y, CB, CR)
|
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals RGB 1 IN S-Video signal
|
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms |
| Terminals RGB 2 IN
|
D-sub HD 15-pin (female) x 1 |
| Terminals RGB 2 IN R, G, B
|
R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. |
| Terminals RGB 2 IN Y, PB, PR (Y, CB, CR)
|
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals VIDEO IN
|
BNC x 1, 1.0 Vp-p, 75 ohms |
| Terminals SERIAL IN
|
D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
| Terminals SERIAL OUT
|
D-sub 9-pin (male) x 1 for link control(RS-232C compliant) |
| Terminals Remoter 1 In
|
M3 jack x 1 for wired remote control |
| Terminals Remoter 1 Out
|
M3 jack x 1 for link control |
| Terminals Remoter 2 In
|
D-sub 9-pin x 1 for external control (parallel) |
| Terminals LAN
|
RJ-45 x 1 for network connection, 100Base-TX/10Base-T, compliant with PJLink™ (class 1) |
| Power cord length
|
3.0 m (9 ft 10 in) |
| Cabinet materials
|
Molded plastic |
| Dimensions (W x H x D)
|
530 x 200 x 548.5 mm (20-7/8 x 7-7/8 x 21-19/32 inches) (without lens) |
| Weight
|
24 kg (52.9 lbs) (without lens) |
| Operation noise
|
43 dB (normal mode), 37 dB (eco mode) |
| Operating temperature
|
0℃ - 45℃ (32℉ - 113℉) |
| Operating humidity
|
10% - 80% (no condensation) |
| Technology
|
3-Chip DLP |
