| Specification |
Description |
| Brightness
|
10,000 lumens |
| Resolution
|
5,120 x 3,200 pixels (Quad Pixel Drive: ON) |
| Lamp
|
3-Chip DLP Laser |
| Power supply
|
AC 100-240 V, 50/60 Hz
(Note: Brightness may decrease depending on power conditions) |
| Power consumption
|
1,270 W (0.3 W with STANDBY MODE set to ECO. 4 W with
STANDBY MODE set to NORMAL.),
Average power consumption
NORMAL: 913W ECO: 782W LONG LIFE1: 531-732W
LONG LIFE 2: 477-702W LONG LIFE 3: 423-665W
*Operating Temperature: 25 °C (77 °F), Altitude: 700m (22 ft 12 in),
ICE627087: 2008 Broadcast contents,
Picture mode: Dynamic, Dynamic Contrast3 |
| DLP™ chip | Panel size
|
22.9 mm (0.9 inches) diagonal (16:10 aspect ratio) |
| DLP™ chip | Display method
|
DLP™ chip x 3 (R, G, B), DLP™ projection system |
| DLP™ chip | Pixels
|
4,096,000 (2,560 x 1,600) x 3, total of 12,288,000 pixels
49,152,000 (12,288,000 x 4) pixels when Quad Pixel Drive set to ON |
| Refresh Rate
|
240 Hz |
| LENS
|
Optional powered zoom/focus lenses |
| Light source
|
Laser Diode (Laser class: Class 1)*Class 3R for North America.
Luminance life for set: 20,000 hours at half luminance (normal)/
24,000 hours at half luminance (Eco)
* Temperature: 35°C (95°F), Altitude 700m (22ft 12in), Dust: 0.15mg/m³
43,800 hours at constant luminance (Longlife1)
61,320 hours at constant luminance (Longlife2)
87,600 hours at constant luminance (Longlife3) |
| Screen size
|
1.78-25.4 m (70-1,000 inches) (16:10 aspect ratio)
1.78-15.24 m (70 - 600 inches) with the ET-D75LE8 (16:10 aspect ratio)
3.05-15.24 m (120 - 600 inches) with the ET-D75LE90 (16:10 aspect ratio) |
| Center-to-corner uniformity
|
90% |
| Contrast
|
20,000:1 (full on/full off, in Dynamic Contrast 3 mode) |
| Scanning frequency | SDI
|
SD-SDI signal SMPTE ST 259 compliant (YCBCR 4:2:2 10-bit): 480i, 576i
Single-link HD-SDI signal SMPTE ST 292 compliant(YPBPR 4:2:2 10-bit):
720/60p, 720/50p, 1035/60i, 1080/60i, 1080/50i, 1080/25p, 1080/25sF,
1080/24p, 1080/24sF, 1080/30p, 1080/30sF
Single-link 3G-SDI signal SMPTE ST 424 compliant (YPBPR 4:2:2 10-bit):
1080/60p, 1080/50p, 2048 x 1080/48p, 2048 x 1080/50p, 2048 x 1080/60p,
(RGB 4:4:4 12-bit/10-bit, YPBPR 4:4:4 12-bit/10-bit): 1080/60i, 1080/50i,
1080/25p, 1080/25sF, 1080/24p, 1080/24sF, 1080/30p, 1080/30sF, (RGB
4:4:4 12-bit/10-bit, YPBPR 4:4:4 12-bit/10-bit, X'Y'Z' 4:4:4 12-bit):
2048 x 1080/24p, 2048 x 1080/24sF, 2048 x 1080/25p, 2048 x 1080/25sF,
2048 x 1080/30p, 2048 x 1080/30sF
Dual-link HD-SDI signal SMPTE ST 372 compliant(YPBPR 4:2:2 10-bit):
1080/50p, 1080/60p, (RGB 4:4:4 12-bit/10-bit, YPBPR 4:4:4 12-bit/10-bit):
1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/25sF, 1080/30p,
1080/30sF, 2048 x 1080/24p, 2048 x 1080/24sF, 2048 x 1080/25p,
2048 x 1080/25sF, 2048 x 1080/30p, 2048 x 1080/30sF, (X' Y' Z' 4:4:4
12-bit*3): 2048 x 1080/24p, 2048 x 1080/24sF, 2048 x 1080/25p,
2048 x 1080/25sF, 2048 x 1080/30p, 2048 x 1080/30sF
Dual-link 3G-SDI signal SMPTE ST 425 compliant (YPBPR 4:4:4 12-bit/10-bit):
1080/50p, 1080/60p, 2048 x 1080/48p, 2048 x 1080/50p, 2048 x 1080/60p,
(RGB 4:4:4 12-bit/10-bit) : 1080/50p, 1080/60p, 2048 x 1080/48p,
2048 x 1080/50p, 2048 x 1080/60p, (YPBPR 4:2:2 10-bit): 3840 x 2160/24p,
3840 x 2160/25p, 3840 x 2160/30p, 4096 x 2160/24p, 4096 x 2160/25p,
4096 x 2160/30p
Quad-link HD-SDI signal (YPBPR 4:2:2 10-bit) :
3840 x 2160/24sF, 3840 x 2160/24p, 3840 x 2160/25sF, 3840 x 2160/25p,
3840 x 2160/30sF, 3840 x 2160/30p, 4096 x 2160/24sF, 4096 x 2160/24p,
4096 x 2160/25sF, 4096 x 2160/25p, 4096 x 2160/30sF, 4096 x 2160/30p
Quad-link 3G-SDI signal SMPTE ST 425 compliant (YPBPR 4:2:2 10-bit)：
3840 x 2160/60p, 3840 x 2160/50p, 4096 x 2160/60p, 4096 x 2160/50p,
(YPBPR 4:2:2 12-bit, YPBPR 4:4:4 10-bit/12-bit, RGB 10-bit/12-bit)
3840 x 2160/24sF, 3840 x 2160/24p, 3840 x 2160/25sF, 3840 x 2160/25p,
3840 x 2160/30sF, 3840 x 2160/30p, 4096 x 2160/24sF, 4096 x 2160/24p,
4096 x 2160/25sF, 4096 x 2160/25p, 4096 x 2160/30sF, 4096 x 2160/30p
SDI1/SDI2 Simultaneous inputs (2 x speed): 1080/60p, 1080/50p
(1st FRAME: SDI1, 2nd FRAME: SDI2)
SDI1/SDI2/SDI3/SDI4 Simultaneous inputs (4 x speed): 1080/60p, 1080/50p
(1st FRAME: SDI1, 2nd FRAME: SDI2, 3rd FRAME: SDI3, 4th FRAME: SDI4)
DIGITAL LINK: Movie signal resolution : 480i/576i - 4096 x 2160,
Still picture signal resolution : 640 x 400 - 2560 x 1600 (non-interlace),
Dot clock frequency: 25 MHz - 297 MHz |
| Keystone correction range
|
Vertical: ±40° (±22° with the ET-D75LE50, ±28° with the ET-D75LE6, +5° with the ET-D75LE90), horizontal: ±15° (0° with the ET-D75LE90) |
| Optical axis shift | Vertical
|
±59% (±44% with the ET-D75LE6), (+74-84% with the ET-D75LE90),
from center of screen, powered |
| Optical axis shift | Horizontal
|
±29% (±19% with the ET-D75LE6), (-12-16% with the ET-D75LE90),
from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50. |
| Installation
|
Ceiling/floor, front/rear |
| Terminals | SDI IN 1
|
BNC x 1,
3G/HD/SD-SDI input, Dual-link input (LINK-A) ,
Quad-link input
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual-link HD-SDI signal SMPTE ST 372 compliant
Dual-link 3G-SDI signal SMPTE ST 425 compliant
Quad-link HD-SDI signal
Quad-link 3G-SDI signal SMPTE ST 425 compliant |
| Terminals | SDI IN 2
|
BNC x 1,
3G/HD/SD-SDI input, Dual-link input (LINK-B) ,
Quad-link input
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual-link HD-SDI signal SMPTE ST 372 compliant
Dual-link 3G-SDI signal SMPTE ST 425 compliant
Quad-link HD-SDI signal
Quad-link 3G-SDI signal SMPTE ST 425 compliant |
| Terminals | SDI IN 3
|
BNC x 1,
3G/HD/SD-SDI input, Dual-link input (LINK-A) ,
Quad-link input
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual-link HD-SDI signal SMPTE ST 372 compliant
Dual-link 3G-SDI signal SMPTE ST 425 compliant
Quad-link HD-SDI signal
Quad-link 3G-SDI signal SMPTE ST 425 compliant |
| Terminals | SDI IN 4
|
BNC x 1,
3G/HD/SD-SDI input, Dual-link input (LINK-B) ,
Quad-link input
SD-SDI signal SMPTE ST 259 compliant
HD-SDI signal SMPTE ST 292 compliant
3G-SDI signal SMPTE ST 424 compliant
Dual-link HD-SDI signal SMPTE ST 372 compliant
Dual-link 3G-SDI signal SMPTE ST 425 compliant
Quad-link HD-SDI signal
Quad-link 3G-SDI signal SMPTE ST 425 compliant |
| Terminals | Frame Sync IN/OUT
|
BNC x 1, (frame-synchronizing timing signal) |
| Terminals | Frame Sync OUT
|
BNC x 1, (frame-synchronizing timing signal) |
| Terminals | SERIAL IN
|
D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
| Terminals | SERIAL OUT
|
D-sub 9-pin (male) x 1 for link control |
| Terminals | Remoter 1 In/Out
|
M3 x 1 for link control (for wired remote control) |
| Terminals | REMOTE 2 IN
|
D-sub 9-pin (female) x 1 for external control (parallel) |
| Terminals | DIGITAL LINK/LAN
|
RJ-45 x 1 (for network, DIGITAL LINK connection (HDBaseT™ compatible),
100Base-TX,compatible with Art-Net, PJLink™ (class 1), Deep Color, HDCP2.2) |
| Terminals | Expansion Slot
|
x 2 (SLOT 1，SLOT 2), SLOT NX (Compatible with Optional Board) |
| Power cord length
|
3.0 m (9 ft 10 in) |
| Cabinet materials
|
Molded plastic |
| Dimensions (W x H x D)
|
578 x 323.5 x 740 mm
(22-3/4 x 12-23/32 x 29-1/8 inches) (with projections)
578 x 270 x 725 mm
(22-3/4 x 10-5/8 x 28-17/32 inches) (without lens, feet or projections) |
| Weight
|
49 kg (108.0 lbs) (without lens) |
| Operating noise
|
46 dB |
| Operating temperature
|
Ambient operating temperature: 0°C to 45°C (32 °F to 113 °F).
Ambient operating humidity: 10% - 80% (no condensation)
When the operating mode is set to "Normal", the operating temperature range is 0°C to 45°C (32 °F to 113 °F), and at altitudes from 1,400 m to 4,200 m
(4,593 ft to 13,780 ft) it is 0°C to 40°C (32 °F to 104 °F).
When the operating mode is set to "Eco", or "Long Life 1/2/3", the operating
temperature range is 0°C to 40°C (32 °F to 104 °F).
When the projector is used with a Smoke Cut Filter, the operating temperature range is 0°C to 35°C (32 °F to 95 °F).
Furthermore, when the operating mode is set to "Eco", or "Long Life 1/2/3",the projector cannot be used at altitudes above 2700 m (8,858 ft). In addition,
when the projector is used with a Smoke Cut Filter, it cannot be used at altitudes above 1,400 m (4,593 ft). The brightness of the light source may drop depending on the operating environment and the operating temperature range in order to protect the projector. |
| Applicable software
|
Logo Transfer Software, Multi Monitoring & Control Software,
Early Warning Software,Geometry Manager Pro (ET-UK20 series Upgrade Kit and ET-CUK10 series Auto Screen Adjustment Kit) |
| Technology
|
3-chip DLP Laser |
