PT-DZ21K2U 3-Chip DLP™ Large Venue Projector

 
  • Chat with Sales

  • Contact us
  • Add to Briefcase
  • Share

PT-DZ21K2

Product details

Compact 20000 lumens-class Projector Flagship model delivering spellbinding picture quality for events and staging

Key features
  • 3-chip DLP, 20000 lumens, WUXGA
  • 120Hz high frame rate for superb and sharp motion pictures
  • Compact design, light weight and low noise level (as low as 46db)
  • Quad-lamp redundancy for failsafe operation
  • Fully featured for single or multi-mapping installations
  • Thumbnail
  • Thumbnail
  • Thumbnail
  • Thumbnail
View Product Support

Chat with Sales

Brightness 20,000 lumens (four lamp)
Resolution 1,920 x 1,200 pixels (Input signals that exceed this resolution will be converted to 1,920 x 1,200 pixels.)
Technology 3-Chip DLP
Power supply 200 - 240 V AC, 12 A, 50/60 Hz (3-wire single-phase)
Power consumption 2,060 W (2,100 VA) (0.3 W with STANDBY MODE set to ECO. 9 W with
STANDBY MODE set to NORMAL.),
max. 7,031 BTU (without light output: 6,758 BTU )
DLP™ chip | Panel size 24.4 mm (0.96 inches) diagonal (16:10 aspect ratio)
DLP™ chip | Display method DLP™ chip x 3 (R, G, B), DLP™ projection system
DLP™ chip | Pixels 2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels
LENS Optional powered zoom/focus lenses
Lamp 432 W UHM lamps (x 4) (four lamp system)
Screen size 1.78-25.4 m (70-1,000 inches) (1.78-15.24 m (70-600 inches) with
the ET-D75LE8), 16:10 aspect ratio
Center-to-corner uniformity 90%
Contrast 10,000:1 (full on/full off, in dynamic iris 3 mode)
Scanning frequency | SDI Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 372 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 2048 x 1080/24p, 2048/1080/24sF
Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit):
SMPTE ST 372 compliant: 2048 x 1080/24p, 2048 x 1080/24sF,
3G-SDI signal (RGB 4:4:4 12-bit/10-bit):
SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p,
3G-SDI signal (YPBPR 4:2:2 10-bit):
SMPTE ST 424 compliant: 1080/50p, 1080/60p,
HD-SDI signal (YPBPR 4:2:2 10-bit):
SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i,
1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p,
SD-SDI signal (YCBCR 4:2:2 10-bit):
SMPTE ST 259 compliant: 480i, 576i
Scanning frequency | HDMI/DVI-D/DIGITAL LINK Horizontal: 15-100 kHz, vertical: 24-120 Hz,
dot clock: 25-162 MHz
Scanning frequency | RGB Horizontal: 15-100 kHz, vertical: 24-120 Hz,
dot clock: 162 MHz or less
Scanning frequency | YPBPR (YCBCR) 480i (525i): fH 15.73 kHz; fV 59.94 Hz,
576i (625i): fH 15.63 kHz; fV 50 Hz,
480p (525p): fH 31.47 kHz; fV 59.94 Hz,
576p (625p): fH 31.25 kHz; fV 50 Hz,
720 (750)/60p: fH 45.00 kHz; fV 60 Hz,
720 (750)/50p: fH 37.50 kHz; fV 50 Hz,
1035/60i: fH 33.75 kHz; fV 60 Hz,
1080 (1125)/60i: fH 33.75 kHz; fV 60 Hz,
1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz,
1080/25p: fH 28.13 kHz; fV 25 Hz,
1080/24p: fH 27.00 kHz; fV 24 Hz,
1080/24sF: fH 27.00 kHz; fV 48 Hz,
1080/30p: fH 33.75 kHz; fV 30 Hz,
1080/60p: fH 67.50 kHz; fV 60 Hz,
1080/50p: fH 56.25 kHz; fV 50 Hz
Scanning frequency | Video/Y/C fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift | Vertical ±55% (±44% with the ET-D75LE6, +73-+78% with the ET-D75LE90)
from center of screen, powered
Optical axis shift | Horizontal ±20% (±15% with the ET-D75LE6, ±6% with the ET-D75LE90)
from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the
ET-D75LE50.
Keystone correction range Vertical : ±40° (±22° with the ET-D75LE50, ±28° with the ET-D75LE6,
+5° with the ET-D75LE90), horizontal: ±15°
Installation Ceiling/floor, front/rear
Terminals | SDI IN 1 BNC x 1,
Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 1)
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A)
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
Terminals | SDI IN 2 BNC x 1,
Dual-link 3G-SDI signal: SMPTE ST 425 compliant (Link 2)
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B)
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
Terminals | HDMI IN HDMI 19-pin x 1, Deep Color, compatible with HDCP
Terminals | DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible,
for single link only
Terminals | DIGITAL LINK/LAN RJ-45 Network connection / digital link connection (video/network/serial
control) compliant with PJLink,100base-tx, Art-Net compatible
Deep Color, compatible with HDCP
Terminals | RGB 1 IN BNC x 5
Terminals | RGB 1 IN | R, G, B R: 0.7 Vp-p, 75 o hms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals | RGB 1 IN | Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals | RGB 1 IN | S-Video signal Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
Terminals | RGB 2 IN D-sub HD 1 5-pin (female) x 1
Terminals | RGB 2 IN | R, G, B R: 0.7 Vp-p, 75 o hms,
G: 0.7 Vp-p ( G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Terminals | RGB 2 IN | Y, PB, PR (Y, CB, CR) Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Terminals | 3D SYNC 1 IN/OUT BNC x 1, 1.0 Vp-p, 75 ohms
Input: TTL, high impedance. Output: TTL, max. 10 mA
Terminals | 3D SYNC 2 OUT BNC x 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
Terminals | SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
Terminals | SERIAL OUT D-sub 9-pin (male) x 1 for link control
Terminals | Remoter 1 In M3 jack x 1 for wired remote control
Terminals | Remoter 1 Out M3 jack x 1 for link control
Terminals | Remoter 2 In D-sub 9-pin (female) x 1 for external control (parallel)
Power cord length 3.0 m (9 ft 10 in)
Cabinet materials Molded plastic
Dimensions (W x H x D) 620 x 291 x 800 mm
(24-7/16 x 11-15/32 x 31-1/2 inches) (without lens)
Weight Approx. 41 kg (90.4 lbs) (without lens)
Operating noise 46 dB (quad lamp operation)
Operating temperature 0°- 45°C (32°- 113°F)
Operating humidity 10%-80% (no condensation)
Keystone Correction Range with Optional Upgrade Kit Vertical: ±45° (±40° with the ET-D75LE10/ET-D75LE20,
±22° with the ET-D75LE50, ±28° with the ET-D75LE6),
horizontal: ±40° (±15° with the ET-D75LE50/ET-D75LE6)
<sup>(1)</sup> Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.<br/>
<sup>(2)</sup> Maximum physical resolution. Quad Pixel Drive: ON.<br/>
<sup>(3)</sup> Measured at center area of projector screen. Measurement method is in compliance with ISO/IEC 21118: 2012 international standards. Value is average of all products when shipped.<br/>
<sup>(4)</sup> With lens other than ET-D75LE95 and power supply of AC 200 V.