| Specification |
Description |
| Power supply
|
120-240 V AC, 10-5.2 A, 50/60 Hz |
| Power Consumption (120-240V AC, 50/60Hz)
|
1,030 W(1,060 VA) (0.3 W with STANDBY MODE set to ECO, 3 W with STANDBY MODE set to NORMAL) |
| DLP™ chip Panel size
|
17.8 mm (0.7 in) diagonal (4:3 aspect ratio) |
| DLP™ chip Display method
|
DLP™ chip x 1, DLP™ system |
| DLP™ chip Pixels
|
786,432 (1,024 x 768) x 1, total of 786,432 pixels |
| Lens PT-DX100K/DX100W
|
Powered zoom/focus lenses (1.8 - 2.5:1), F 1.7 - 1.9, f 25.6 - 35.7 mm |
| Lens PT-DX100LK/DX100LW
|
Optional powered zoom/focus lenses and fixed-focus lens |
| Lamp
|
420 W UHM lamps (x 2) |
| Screen size
|
1.27-15.24 m (50-600 inches), 1.27-5.08 m (50-200 inches) with the ET-DLE055 (4:3 aspect ratio), 2.54-8.89 m (100-350 inches) with the ET-DLE030 (4:3 aspect ratio) |
| Brightness
|
10,000 lumens (dual lamp, LAMP MODE: NORMAL) |
| Center-to-corner uniformity
|
90% |
| Contrast
|
10,000:1 (full on/full off, in dynamic iris 3 mode) |
| Resolution
|
1,024 x 768 pixels (Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.) |
| Scanning Frequency (HDMI/DVI-D)
|
fH: 15 - 100 kHz, fV: 24 - 120 Hz, dot clock: 25 - 162 MHz |
| Scanning Frequency (RGB)
|
fH: 15 - 100 kHz, fV: 24 - 120 Hz, dot clock: 162 MHz or lower |
| Scanning frequency YPBPR (YCBCR)
|
525i(480i): fH 15.75 kHz; fV 60 Hz, 625i(576i): fH 15.63 kHz; fV 50 Hz,525p(480p): fH 31.50 kHz; fV 60 Hz, 625p(576p): fH 31.25 kHz; fV 50 Hz, 750(720)/60p: fH 45.00 kHz; fV 60 Hz, 750(720)/50p: fH 37.50 kHz; fV 50 Hz, 1125(1035)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125(1080)/50i: fH 28.13 kHz; fV 50 Hz, 1125(1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125(1080)/24p: fH 27.00 kHz; fV 24 Hz, 1125(1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125(1080)/30p: fH 33.75 kHz; fV 30 Hz, 1125(1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125(1080)/50p: fH 56.25 kHz; fV 50 Hz |
| Scanning Frequency (Video/S-Video)
|
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PALM/PAL60]; fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
| Optical axis shift
|
Vertical: +50% (powered) (±45° with the ET-DLE085/ET-DLE105), Horizontal: ±10% (powered); NOTE: Optical axis shift function cannot be operated when used with the ET-DLE055. If using the ET-DLE030, the optical axis is fixed. |
| Keystone correction range
|
Vertical ±40°; ±30° with the ET-DLE055/ET-DLE085/ET-DLE105. Cannot be used when the ET-DLE030 is installed. |
| Installation
|
Ceiling/floor, front/rear |
| Terminals HDMI IN
|
HDMI 19-pin x 1, Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz; NOTE: Compatible with non-interlaced signals only. |
| Terminals DVI-D IN
|
DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link only; 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)/50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz; NOTE: Compatible with non-interlaced signals only. |
| Terminals RGB 1 IN
|
BNC x 5 |
| Terminals RGB 1 IN R, G, B
|
R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. |
| Terminals RGB 1 IN Y, PB, PR (Y, CB, CR)
|
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals RGB 1 IN S-Video signal
|
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms |
| Terminals RGB 2 IN
|
D-sub HD 15-pin (female) x 1 |
| Terminals RGB 2 IN R, G, B
|
R: 0.7 Vp-p, 75 ohms; G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms; B: 0.7 Vp-p, 75 ohms; HD, VD/SYNC: TTL, high impedance, positive/negative automatic; NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. |
| Terminals RGB 2 IN Y, PB, PR (Y, CB, CR)
|
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
| Terminals 3D SYNC 1 IN/OUT
|
BNC x 1, 1.0 Vp-p, 75 ohms; Input: TTL, high impedance. Output: TTL, max. 10 mA |
| Terminals 3D SYNC 2 OUT
|
BNC x 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA |
| Terminals VIDEO IN
|
BNC x 1, 1.0 Vp-p, 75 ohms |
| Terminals SERIAL IN
|
D-sub 9-pin (female)x 1 for external control (RS-232C compliant) |
| Terminals SERIAL OUT
|
D-sub 9-pin (male) x 1 for link control (RS-232C compliant) |
| Terminals Remoter 1 In
|
M3 jack x 1 for wired remote control |
| Terminals Remoter 1 Out
|
M3 jack x 1 for link control |
| Terminals Remoter 2 In
|
D-sub 9-pin (female)x 1 for external control (parallel) |
| Terminals LAN/DIGITAL LINK
|
RJ-45 x 1 for network and DIGITAL LINK (video/network/serial control) connection, 100Base-TX, compatible with Art-Net, compliant with PJLink™ (class 1), Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p; VGA(640 x 480) - WUXGA(1,920 x 1,200), dot clock: 25 MHz - 162 MHz; NOTE: Compatible with non-interlaced signals only. |
| Power cord length
|
3.0 m (9 ft 10 in) |
| Cabinet materials
|
Molded plastic |
| Dimensions (W x H x D) PT-DX100K / DX100W
|
498 x 200 x 556 mm (19-19/32 x 7-7/8 x 21-7/8 inches) (with supplied lens)" |
| Dimensions (W x H x D) PT-DX100LK / DX100LW
|
498 x 200 x 513 mm (19-19/32 x 7-7/8 x 20-3/16 inches) (without lens)" |
| Weight PT-DX100K/DX100W
|
Approx. 18.3 kg (40.3 lbs) (with supplied lens) |
| Weight PT-DX100LK/DX100LW
|
Approx. 17.6 kg (38.8 lbs) (without lens) |
| Operation noise
|
40 dB (dual lamp operation, LAMP MODE: NORMAL), 35 dB (dual lamp operation, LAMP MODE: ECO) |
| Operating temperature
|
0℃ - 45 ℃ (32℉ - 113℉) |
| Operating humidity
|
10% - 80% (no condensation) |
| Technology
|
1-Chip DLP |
| Note
|
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the STANDBY MODE is set to ECO, network functions such as power on over the LAN network will not operate, and the serial output terminal
cannot be used. Also, only certain commands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*4 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5 With legs at shortest position.
*6 Average value. May differ depending on models.
*7 The operating temperature range is 0 °C to 40 °C (32 °F to 104 °F) when the fan control is set to High Altitude mode (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). Also, if the ambient temperature exceeds 40 °C (104 °F) (35 °C (95 °F) in High Altitude mode) when the projector is being used with Lamp Select set to Dual and Lamp Power set to High, the light output may be reduced approximately 20% to protect the projector.
*8 Operation range differs depending on environments. |
