Sorry, you need to enable JavaScript to visit this website.

PT-RDQ10 1-Chip DLP® 4K Laser Projector

  • Chat with Sales
  • Contact us

PT-RDQ10 Available Fall 2021

Key features

  • Laser 1-Chip DLP, 10,000 lumens (ANSI), 4K laser projector
  • Rich Colour Harmonizer technology for improved and more accurate colour reproduction
  • Projects crisp, smooth, and richly detailed 4K (3840 x 2160, 16:9) images.
  • Maintenance-free up to 20,000 hours maintenance-free operation with dust-resistant optical block and long lasting laser engine
  • 4K Professional (Silver)
  • 4k Digital Link
  • NX Slot
  • 24/7 Operation
  • Solid Shine Laser
  • Geo Pro
  • 360-Degree Free Installation
View Product Support

Chat with Sales

Specification Description
LENS Powered zoom (throw ratio 1.60–2.58:1), powered focus (for supplied lens; optional lenses also available)
Resolution 4K (3840 x 2160 pixels) (With Smooth Pixel Drive)
Keystone correction range TBD
Installation Ceiling/floor, front/rear, free 360-degree installation
Screen Size (Diagonal) 1.52–15.24 m (60–600 in) with ET-DLE060/ET-DLE088/ET-DLE158/ET-DLE178*4 /ET-DLE258, 2.54–10.16 m (100–400 in) with ET-DLE020, 16:9 aspect ratio
Contrast Ratio*1 10,000:1 (Full On/Full Off) (When [PICTURE MODE] is set to [DYNAMIC] and [DYNAMIC CONTRAST] is set to [3]. HDMI signal input)
Light source Laser diodes
Terminals | SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
DLP™ chip | Panel size 16.8 mm (0.66 in) diagonal (16:9 aspect ratio)
DLP™ chip | Display method DLP™ chip x 1, DLP™ projection system
Terminals | SERIAL OUT D-sub 9-pin (male) x 1 for link control (RS-232C compliant)
Terminals | MULTI PROJECTOR SYNC IN BNC x 1
Terminals | MULTI PROJECTOR SYNC OUT BNC x 1
Terminals | HDMI 1 IN HDMI 19-pin x 2 (Compatible with HDCP 2.3, Deep Color, 4K/60p signal input)
Projector type 1-Chip DLP™ projector
DLP™ chip | Number of Pixels 2716 x 1528 pixels (Images cannot be displayed at this resolution)
Center-to-corner zone ratio*1 90 %
Time until light output declines to 50 %*3 20,000 hours (NORMAL/QUIET)/24,000 hours (ECO)
Lens shift | Vertical(From the origin point of the lens mounter) ±60 % with ET-DLE088/ET-DLE158/ET-DLE178*4/ET-DLE258 (±49 % with ET-DLE060, +59 %, -40 % with ET-DLE020) (powered)
Lens shift | Horizontal(From the origin point of the lens mounter) ±25 % with ET-DLE088/ET-DLE158/ET-DLE178*4/ET-DLE258 (±19 % with ET-DLE060, ±24 % with ET-DLE020) (powered)
Light Output*1 *2 10,000 lm
Power consumption TBD
Operating environment Operating temperature: 0–45 °C (32–113 °F)*7 *8 , operating humidity: 10–80 % (no condensation)
Cabinet materials Molded plastic
Applicable software Logo Transfer Software, Multi Monitoring & Control Software, Early Warning Software, Geometry Manager Pro, Smart Projector Control for iOS/Android™
Weight*6 Less than 25 kg (55.1 lbs) excluding lens [TBD]
Note *1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2020 international standards. Value is average of all products when shipped. *2 When [PICTURE MODE] is set to [DYNAMIC] and [LIGHT POWER] is set to [NORMAL]. *3 Around this time, lightoutput will have decreased to approximately 50 % of its original level ([PICTURE MODE]: [DYNAMIC], [DYNAMIC CONTRAST] set to [3], temperature 35 °C (86 °F), elevation 700 m (2,297 ft) with 0.15 mg/m3 of particulate matter). Estimated time until light output declines to 50 % variesdepending on environment. *4 ET-DLE178 is equivalent of supplied lens. Availability of ET-DLE178 varies depending on country. *5 With legs fully retracted, excluding lens and protruding parts. *6 Average value. May differ depending on the actual unit. *7 When using the projector at analtitude lower than 2,700 m (8,858 ft) above sea level, and the operating environment temperature becomes 30 °C (86 °F) or higher, the light output may be reduced to protect the projector. When using the projector at an altitude between 2,700 m (8,858 ft) and 4,200 m (13,780 ft), and theoperating environment temperature becomes 25 °C (77 °F) or higher, the light output may be reduced to protect the projector. *8 When optional AJ-WM50 Series wireless module is attached, operating temperature range becomes 0–40 °C (32–104 °F).
Power supply AC 100–240 V, 50/60 Hz
Terminals | DC OUT USB Connector (Type A) x 1 (Output 5 V/2 A)
Terminals | USB USB Connector (Type A) x 1 for Cloning/Wireless Module (Output 5 V/500 mA)
Terminals | REMOTE 2 IN D-sub 9-pin (female) x 1 for external control (parallel)
Terminals | Expansion Slot Open slot for SLOT NX compatible interface board
Terminals | REMOTE 1 IN M3 stereo mini-jack x 1 for wired remote control
Terminals | REMOTE 1 OUT M3 stereo mini-jack x 1 for link control (for wired remote control)
Operation noise*1 39 dB (NORMAL/ECO) [TBD] / 35 dB (QUIET) [TBD]
Dimensions (W × H × D)*5 498 x 200 x 538 mm (19 19/32˝ x 7 7/8˝ x 21 3/16˝ ) excluding lens [TBD]
Terminals | DIGITAL LINK/LAN RJ-45 x 1 for network and DIGITAL LINK connection (video/network/serial control) (HDBaseT™ compliant), 100Base-TX (Compatible with PJLink™ [Class 2], Art-Net, HDCP 2.3, Deep Color,4K/60p signal input)
Terminals | LAN RJ-45 x 1 for network connection, 10Base-T, 100Base-TX (Compatible with PJLink™ [Class 2], Art-Net)