| Specification |
Description |
| Projector type
|
1-Chip DLP™ projector |
| DLP™ chip | Display method
|
DLP™ chip x 1, DLP™ projection system |
| DLP™ chip | Number of Pixels
|
2,304,000 (1920 × 1200) pixels, 4,608,000 (2,304,000 x 2) pixels when 4K Smooth Pixel Drive set to ON |
| Light source
|
Laser diodes |
| Resolution
|
4K-equivalent (4K Smooth Pixel Drive: ON) |
| Screen size [diagonal] (mm)
|
1.27–15.24 m (50–600 in), 1.27–5.08 m (50–200 in) with ET-DLE055, 2.54–8.89 m (100–350 in) with ET-DLE035, 16:10 aspect ratio |
| Screen size [diagonal] (inch)
|
1.27–15.24 m (50–600 in), 1.27–5.08 m (50–200 in) with ET-DLE055, 2.54–8.89 m (100–350 in) with ET-DLE035, 16:10 aspect ratio |
| LENS
|
Optional lenses |
| Keystone correction range
|
Vertical: ±40° (±16° with ET-DLE060, ±22° with ET-DLE105/ET-DLE085/DLE055, +5° with ET-DLE035),Horizontal: ±15° (±10° with ET-DLE060) (cannot be operated with ET-DLE035) |
| Keystone correction range with optional ET-UK20 Upgrade Kit
|
Vertical: ±45° (±16° with ET-DLE060, ±40° with ET-DLE150/DLE250/ET-DLE170, ±22° with ET-DLE105/ET-DLE085/DLE055),Horizontal: ±40° (±10° with ET-DLE060, ±15° with ET-DLE105/ET-DLE085/DLE055),When [VERTICAL KEYSTONE] and [HORIZONTAL KEYSTONE] are used simultaneously, correction cannot be made exceeding a total of 55°. |
| Installation
|
Ceiling/floor, front/rear, free 360-degree installation |
| Terminals | SDI IN
|
BNC x 1: 3G/HD-SDI input |
| Terminals | HDMI IN
|
HDMI 19-pin x 1 (Deep Color, compatible with HDCP 2.2) |
| Terminals | DVI-D IN
|
DVI-D 24-pin x 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only) |
| Terminals | MULTI PROJECTOR SYNC IN
|
BNC x 1 |
| Terminals | MULTI PROJECTOR SYNC OUT
|
BNC x 1 |
| Terminals | SERIAL IN
|
D-sub 9-pin (female) x 1 for external control (RS-232C compliant) |
| Terminals | SERIAL OUT
|
D-sub 9-pin (male) x 1 for link control |
| Terminals | REMOTE 1 OUT
|
M3 x 1 for link control (for wired remote control) |
| Terminals | REMOTE 2 IN
|
D-sub 9-pin (female) x 1 for external control (parallel) |
| Terminals | LAN
|
RJ-45 x 1 for network connection, 10Base-T/100Base-TX, compliant with PJLink™ (Class 2), Art-Net |
| Terminals | Expansion Slot
|
SLOT for interface boards, SLOT NX compatible |
| Power supply
|
AC 100-240 V, 50/60 Hz |
| Power consumption
|
TBD |
| Cabinet materials
|
Molded plastic |
| Operation noise*1
|
TBD |
| Operating environment
|
Operating temperature: 0-45 °C (32-113 °F)*6, operating humidity: 10-80 % (no condensation) |
| Applicable software
|
Logo Transfer Software, Multi Monitoring & Control Software, Geometry Manager Pro, Smart Projector Control for iOS/Android™ |
| Note
|
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2012 international standards. Value is average of all products when shipped. *2 Around this time, light output will have decreased by approximately 50 %. IEC62087: 2008 Broadcastcontents, NORMAL Mode, Dynamic Contrast [ON], under conditions with 35 °C (95 °F), 700 m (2,297 ft) above sea level, and 0.15 mg/m3 of particulate matter. Estimated time until light output declines to 50 % varies depending on environment. *3 Lens shift is not supported on theET-DLE055, and the optical axis is fixed with the ET-DLE035. *4 With legs at shortest position. *5 Average value. May differ depending on the actual unit. *6 When using the projector at an altitude lower than 2,700 m (8,858 ft) above sea level, and the operating environment temperaturebecomes 30 °C (86 °F) or higher, the light output may be reduced to protect the projector. When using the projector at an altitude between 2,700 m (8,858 ft) and 4,200 m (13,780 ft), and the operating environment temperature becomes 25 °C (77 °F) or higher, the light output may bereduced to protect the projector. |
| Terminals | REMOTE 1 IN
|
M3 x 1 for wired remote control |
| Contrast Ratio*1
|
10,000:1 (Full On/Full Off, Dynamic Contrast Mode: ON) |
| Terminals | USB
|
USB Connector (Type A) x 1 for Cloning/Wireless Module (output 5 V/500 mA) |
| Center-to-corner zone ratio*1
|
90 % |
| DLP™ chip | Panel size
|
17.0 mm (0.67 in) diagonal, 16:10 aspect ratio |
| Light output
|
8,000 lm*1 / 8,400 lm (Center)*2 |
| Time until light output declines to 50 %*3
|
20,000 hours (NORMAL) / 24,000 hours (ECO) |
| Lens shift*4 | Vertical (from center of screen)
|
+50 %, -16 % (+40 %, -16 % with ET-DLE060) (powered) |
| Lens shift*4 | Horizontal (from center of screen
|
+30 %, -10 % (+10 %, -20 % with ET-DLE020, +19 %, -10 % with ET-DLE060, +28 %, -10 % with ET-DLE105/ET-DLE085) (powered) |
| Terminals | DIGITAL LINK
|
RJ-45 x 1 for network, DIGITAL LINK connection (HDBaseT™ compliant), 100Base-TX, compatible with Art-Net, PJLink™ (Class 2), Deep Color, HDCP 2.2, 4K/60p signal input*5 |
| Dimensions (W x H x D)
|
PT-RCQ80: 498 x 200*6 x 581 mm (19 19/32 x 7 7/8˝ *6 x 22 7/8˝ ) (with supplied lens)
PT-RCQ80L: 498 x 200*6 x 538 mm (19 19/32˝ x 7 7/8˝ *6 x 21 3/16˝ ) (without lens) |
| Weight*7
|
PT-RCQ80: Approx. 24.2 kg (53.4 lbs) (with supplied lens)
PT-RCQ80L: Approx. 23.4 kg (51.6 lbs) (without lens) |
